Rode Wireless GO II Single + GO II TX

Rode Wireless GO II Single

Ultra-compact complete system for all content creators

who

travel alone. The Wireless GO II SINGLE consists of a transmitter and a receiver module. The transmitter module already contains a microphone that is optimally tuned for voice transmission.

The

receiver module has an analog 3.5 mm TRS output for cameras and a digital USB-C output for Mac/PC, smartphone and iPhone.

Operation is very simple

.

To operate, all you have to do is turn on the two modules and they will connect automatically. Signal quality is at its finest, both analog and digital: crystal clear and ready to transmit immediately. The transmitter and receiver have an internal battery that lasts for at least four hours. The Wireless GO II system has a range of 200 (!) meters with a clear line of sight. The scope of delivery includes a short 3.5 mm TRS cable, 2 fur windshields, two USB-C to USB-A cables and a neoprene carrying bag.

The TX transmitter module
The 4x4 cm small transmitter module has a clip on the back, with which it can be conveniently attached to clothing - preferably to the collar or lapel

.

In case the module is too conspicuous in the picture, you can use the 3.5 mm TRS jack on the side and connect an external microphone there, for example the Lavalier GO. If you want, you can also record the audio signal directly in the transmitter module itself as a backup. For this onboard recording function, the module has a memory chip that is sufficient for over 40 hours of audio. For undisturbed outdoor recordings, you should always use the included fur windshield. It can be easily attached to the transmitter module with its bayonet mount.

The RX receiver

module

The receiver module can be easily attached to the camera's hot shoe. The module is then connected to the camera's microphone input via the supplied TRS cable. Using a suitable USB cable, you can also output the signal digitally to a computer or an Android or iOS device. For the latter, the RØDE SC15 or SC16 cables are suitable. The two buttons on the front can be used to select the output mode, mute the transmitter module, and reduce the output level by a flat 12 dB or 24 dB. The LC display shows the output mode, level and charge status of the receiver and transmitter. If required, you can also activate the safety mode in the receiver module, whereby the signal is output both at full level (TRS peak) and reduced by 20 dB (TRS ring). If an unexpectedly loud sound source causes audible distortion on the main track, you can simply switch to a quieter, undistorted safety track during post-processing.

Compatible with RØDE Central and RØDE Connect
Free RØDE Central software can be used to perform firmware updates, feature enhancements and special settings on the Wireless GO II SINGLE. RØDE Connect is an amazing and very easy to use podcast/streaming software and also free

Rode Wireless GO II TX

Digital microphone transmitter

The Wireless GO II TX already has a high quality microphone built in, which has been optimally tuned for voice transmission. With the clip on the back, the transmitter module can be conveniently attached to clothing. In case the transmitter module is too conspicuous in the picture, you can use the 3.5 mm TRS jack on the side and connect an external microphone there - for example the Lavalier GO or Lavalier II.

The

Wireless GO II TX has built-in audio memory for 40 hours of onboard recording (backup).

Wireless ME uses the toll-free and registration-free 2.4 GHz band for transmission, and the range is a whopping 100 meters with a clear line of sight. The internal LiPo battery takes care of the power supply, you can work for up to 7 hours before you have to recharge the module. Charging, firmware updates and backup transfers are done via the USB-C port on the side.

For outdoor shots, you should always use the included fur windshield

.

Simply pull back its hair and attach the windscreen so that the two white dots on the windscreen line up with the two black dots on the module. Another quarter turn to the right and it sits securely

on the module.